When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
What is the one thing every woodworker needs? Yes, a workbench. Now that you have or at least I am assuming you have worked on so many woodworking projects, you are close to becoming a professional woodworker. You now probably owe yourself a nice woodworking bench. You should also know that a true woodworker never buys his bench from the market, but always builds one himself. But before you start this project, you should know what a workbench is.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period (771 to 476 BC). Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.

Set the table saw fence so the blade is centered on the seam, then push the whole thing through the saw. If the board edges are quite bowed or curvy, you may need a second pass. If so, unscrew the cleats, reclamp the boards across the middle center, then screw on the cleats again. The screws ding up the ends of the boards a little, so cut the boards you’re jointing a bit long, then trim 1/2 in. from each end to remove the screw holes.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.

Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.

Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
×