Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.

It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.

Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.


Here’s a nifty tip—with a nifty tip—from faithful reader Don Ayers: Fill snap-capped sports water bottles with glue and stick them upside down in a hunk of 2×6. Now you don’t have to wait for the glue to run into the neck of the bottle, and the cap will control glue flow (and never get lost!). To holster the glue dispensers, cut holes in the base with a spade bit that’s a smidgen larger than the cap’s diameter.
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.

Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.


From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.

$50 - $100Alaska Dream HouseBathroomBedroomChildren's and Kid's Room Furniture and Toy PlansCraftroomDesk, Desk Systems and Project Table Plansdining roomentry wayFarmhouse Style Furniture PlansIndustrial Style Furniture PlansKids and Toysliving roomModern Style Furniture PlansNursery and BabyofficeRustic Furniture Plansstorage and organizationTeensIntermediateSide and End Table PlansBuffet, Sideboard and Credenza PlansCabinet PlansNightstands
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
What is the one thing every woodworker needs? Yes, a workbench. Now that you have or at least I am assuming you have worked on so many woodworking projects, you are close to becoming a professional woodworker. You now probably owe yourself a nice woodworking bench. You should also know that a true woodworker never buys his bench from the market, but always builds one himself. But before you start this project, you should know what a workbench is.
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.

I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
If you have to pick up long lengths of wood from the lumberyard, throw a spring clamp in the back of your vehicle. Use the clamp to attach the warning flag to the end of the protruding lumber. The clamp’s easy to slip on and off, and you won’t have to fuss around with staples, nails or string. — Steve Parker. Plus: Learn more about how to transport large items in your truck.

Hardwoods are separated into two categories, temperate and tropical hardwoods, depending on their origin. Temperate hardwoods are found in the regions between the tropics and poles, and are of particular interest to wood workers for their cost-effective aesthetic appeal and sustainable sources.[9] Tropical hardwoods are found within the equatorial belt, including Africa, Asia, and South America. Hardwoods flaunt a higher density, around 65lb/cu ft as a result of slower growing rates and is more stable when drying.[9] As a result of its high density, hardwoods are typically heavier than softwoods but can also be more brittle.[9] While there are an abundant number of hardwood species, only 200 are common enough and pliable enough to be used for woodworking.[11] Hardwoods have a wide variety of properties, making it easy to find a hardwood to suit nearly any purpose, but they are especially suitable for outdoor use due to their strength and resilience to rot and decay.[9] The coloring of hardwoods ranges from light to very dark, making it especially versatile for aesthetic purposes. However, because hardwoods are more closely grained, they are typically harder to work than softwoods. They are also harder to acquire in the United States and, as a result, are more expensive.[9]
From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
Finally, as I shared in my post last week on how I learned woodworking, I learned how to use power tools by watching YouTube videos and then just trying them out for myself. I highly recommend this method to learn how to use your power tools. There are lots of videos on specific models of tools too. So, watch a few how-to videos and very importantly, review the tool manual and safety guide for your own tools. Then, go ahead and try the tool out yourself and start using it!
×