Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
Another important factor to be considered is the durability of the wood, especially in regards to moisture. If the finished project will be exposed to moisture (e.g. outdoor projects) or high humidity or condensation (e.g. in kitchens or bathrooms), then the wood needs to be especially durable in order to prevent rot. Because of their oily qualities, many tropical hardwoods such as teak and mahogany are popular for such applications.[9]
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]

While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak.[14] Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses.[14] Aspen is similarly soft, although slightly harder, and readily available and inexpensive.[14] Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture.[14] While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain.[14] Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.[14]
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!

Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
$50 - $100Alaska Dream HouseBathroomBedroomChildren's and Kid's Room Furniture and Toy PlansCraftroomDesk, Desk Systems and Project Table Plansdining roomentry wayFarmhouse Style Furniture PlansIndustrial Style Furniture PlansKids and Toysliving roomModern Style Furniture PlansNursery and BabyofficeRustic Furniture Plansstorage and organizationTeensIntermediateSide and End Table PlansBuffet, Sideboard and Credenza PlansCabinet PlansNightstands
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
Woodworking was essential to the Romans. It provided, sometimes the only, material for buildings, transportation, tools, and household items. Wood also provided pipes, dye, waterproofing materials, and energy for heat.[5]:1Although most examples of Roman woodworking have been lost,[5]:2 the literary record preserved much of the contemporary knowledge. Vitruvius dedicates an entire chapter of his De architectura to timber, preserving many details.[6] Pliny, while not a botanist, dedicated six books of his Natural History to trees and woody plants, providing a wealth of information on trees and their uses.[7]
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
Simply soak a washcloth in water and ring it out a bit so it’s not sopping wet. Put the damp washcloth on the affected area. The water will wick through the wood, and that’s fine. Now, with your iron on its highest setting, place it on the damp washcloth over the affected area, and make small movements back and forth and in circles. Press down firmly and continue until your wash cloth is dry. It won’t take long to evaporate. At this point, the wood fibers are absorbing the water and should expand back to where they were originally. Continue this process and repeat by adding more water until the dents rise up to be flush with the rest of the material.

Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
$50 - $100Alaska Dream HouseBathroomBedroomChildren's and Kid's Room Furniture and Toy PlansCraftroomDesk, Desk Systems and Project Table Plansdining roomentry wayFarmhouse Style Furniture PlansIndustrial Style Furniture PlansKids and Toysliving roomModern Style Furniture PlansNursery and BabyofficeRustic Furniture Plansstorage and organizationTeensIntermediateSide and End Table PlansBuffet, Sideboard and Credenza PlansCabinet PlansNightstands

When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
Cutting a miter joint that closes up perfectly and maintains a 90 degree angle is really satisfying. Unfortunately, it doesn’t always happen. Here’s a quick fix for a slightly open miter joint; rub the shank of a screwdriver along the miter at a steep angle, from both sides of the joint. Chances are, you’ll be the only one that knows it wasn’t perfect to begin with! Try this amazing miter project!

This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.


Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Harbor Freight carries a wide range of high quality woodworking tools that are perfect for the home garage and professional carpentry shop alike. If you have a love of woodcrafting, Harbor Freight has the essential tools and accessories you need to tackle woodworking projects efficiently and safely, no matter your skill level. Our huge selection of drill presses, saws, sanders and planers will see you through countless jobs while our dust collection options keep your workspace clear of sawdust. Whatever you’re looking for, from basic woodworking tools to more specialty items, Harbor Freight has what you need to get the job done.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.[12]

We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
(function(d,a){function c(){var b=d.createElement("script");b.async=!0;b.type="text/javascript";b.src=a._settings.messengerUrl;b.crossOrigin="anonymous";var c=d.getElementsByTagName("script")[0];c.parentNode.insertBefore(b,c)}window.kayako=a;a.readyQueue=[];a.newEmbedCode=!0;a.ready=function(b){a.readyQueue.push(b)};a._settings={apiUrl:"https://woodworker.kayako.com/api/v1",messengerUrl:"https://woodworker.kayakocdn.com/messenger",realtimeUrl:"wss://kre.kayako.net/socket"};window.attachEvent?window.attachEvent("onload",c):window.addEventListener("load",c,!1)})(document,window.kayako||{});
×